F4 1S 12A AIO Brushless Flight Controller
Regular price $44.99 USDWhat is the update of the ELRS 2.4G V2.0 board?
- Support both 1S and 2S battery now. Only 1S supported on V1.0.
- Use SPI ExpressLRS 2.4 receiver with Betaflight firmware.
- Modify the shape of the board to support 85mm whoop frame. Only toothpick frame supported on V1.0.
- Use the lighter and smaller SH connector instead of USB Type-C.
F4 1S 12A AIO Flight Controller - A 1S 12A FC for building lightweight 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this FC that integrates 1S 12A ESC is definitely your best choice.
Now the default firmware for F4 1S 12A AIO Brushless Flight Controller is updated to Betaflight V4.3.0 RC6, which supports ELRS V2.0. Please check the below link to download the firmware.
Download the betaflight_4.3.0_BETAFPVF4SX1280_ELRS2.0.hex
Tons of ExpressLRS items are available now!
Bullet Point
- F4 1S 12A AIO Flight Controller is the best choice for building ultra-lightweight 3" toothpick drones like HX115 SE FPV Quad.
- Most of the 1S flight controllers on the market come with 5A ESC by now, but this FC especially integrates 1S 12A ESC, it can provide more sufficient power for 3" toothpick drones.
- Built-in current meter, 2 programmable RGB LEDs, and SPI Frsky receiver. At the same time, all the pads are left for the external receivers with UART1 and UART2, for buzzers, etc.
- Whoop mounting hole pattern, be compatible with most 1S 3" frames. Large pads are reserved for solder motor cables, this design will make solder easier.
Specification of FC
- Item: F4 1S 12A AIO FC
- Weight: 4.74 g (without power cable and BT2.0 connector)
- CPU: STM32F411CEU6 (100MHZ )
- Six-Axis: MPU6000 (SPI connection)
- Firmware version: betaflight_4.2.0_STM32F411
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: Integrated SPI Frsky Receiver / Futaba Receiver / ELRS Receiver
- Motor Pin Connecter: 1.25mm Header Pins
- Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole)
- USB Port: Type-C (V1.0 board), SH1.0 4-Pin (V2.0 board)
Specification of 1S 12A ESC
- Built-in ESC with 12A continuous and peak 25A current
- Input voltage: 1S Lipo (V1.0 board), 1S-2S (V2.0 board)
- ESC firmware: Z_H_30_REV16_7.HEX
- Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
This new BLHeli_S firmware (named Z_H_30_REV16_7.HEX) is supported by BLHeli Configurator, BLHeliSuite, and Bluejay Configurator for setup.
For download and flash, update to the newest BLHeliSuite-16714902a to support this ESC firmware online. For BLHeli Configurator or Bluejay Configurator, you need to load it local. The ESC firmware is available for download here.
Diagram for F4 1S 12A AIO FC
Below is the diagram for the SPI Frsky version board. UART1, UART2, and SBUS pads are left for external receivers like Frsky XM+, TBS Nano receiver so that a long receiver range is available.
Buzz pads (BUZZ+ and BUZZ-) are invalid directly. It needs some modification to make it works.
Below is the diagram for ELRS 2.4G V1.0 board.
Below is the diagram for ELRS 2.4G V2.0 board.
The current meter is integrated on the FC board. Here is the configuration in Betaflight Configurator.
12A 1S ESC
Should we really need a 12A ESC for 1S drones? If it is a 65mm or 75mm Whoop drone-like Meteor65, 5A ESC is enough for all actions. But how about with 3" propellers and 1102/1202.5 motors? Still, want smooth and powerful flying actions? The 5A ESC has developed about 3 years ago and was designed for whoop drones with 0603/0802 motors. For the past year, the BETAFPV team has been cooperating with BLHeli author Steffen on the 12A 1S ESC for 3" toothpick drones. Finally, it is here!
It marks "1-2S" on the board, could this FC board support 2S?
The V1.0 board is NOT support 2S battery. Please choose the V2.0 board for both 1S and 2S battery supported.
ELRS 2.4G RX
This board integrates the receiver with the most popular radio link ExpressLRS in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.
This board is designed for long-range 3inch ultralight toothpick drones or 2S whoop drones. If you want to try ExpressLRS on 65mm/75mm whoop drones, please stay tuned on our F4 1S FC board with a built-in SPI ExpressLRS receiver.
How to Bind with Betaflight FC with ExpressLRS Receiver.
How to update the ELRS RX on the AIO board. (For ELRS 2.4G V1.0 version, ELRS receiver communicates with FC F411 via CRSF protocol. )
Betaflight Firmware and CLI (SPI ELRS 2.4G)
This paragraph is only for ELRS 2.4G V2.0 board, with SPI ELRS 2.4G receiver integrated.
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
Please change the “PID loop frequency” to “4KHZ” , sometimes it would make the SPI receiver not working correct while the value is “8KHZ”.
New released firmware BTFL_4.3.0_BETAFPVF4SX1280_0265565fa uses external GPIO interrupt triggers to process ELRS data reception, increasing the stability of the signal link. Now it can perfectly support LiteRadio 2 SE 500Hz link and modify the accuracy of signal strength.
The new CLI file is named BTFL_cli_F4 12A ELRS_V2.0_NEW. Please check.
Note: The new firmware supports only ELRS 1.0.0, 1.0.1, 1.1.0, 1.2.0, 1.2.1.
Download the firmware and CLI dump file for the F4 1S 12A FC (ELRS 2.4G) board.
How to Bind with Betaflight FC with SPI ExpressLRS Receiver.
More details and discussion on Github about SPI ELRS receiver.
SPI Frsky RX
Come with the build-in SPI Frsky Receiver (CC2500 chip), F4 1S 12A AIO FC can be compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default protocol is configured to Frsky D16 FCC out of the factory. Pilots could set up the protocol according to your own need in Betaflight Configurator.
|
Configuration |
Protocol |
|
FRSKY_D |
Frsky D8 |
| FRSKY_X |
Frsky D16 FCC (ACCST 1.X version) |
|
FRSKY_X_LBT |
Frsky D16 LBT (ACCST 1.X version) |
|
SFHSS |
Futaba S-FHSS |
How to Bind with Betaflight FC with SPI Frsky Receiver.
Recommend Parts
If you want to try the popular ExpressLRS receiver version for long-range performance, highly recommend you to check the items for the ExpressLRS series.
- Recommend for drones like HX115 SE Toothpick Drone / HX115 LR Toothpick Drone
- Battery: BT2.0 450mAh 1S 30C Battery
- Motor: 1102 18000KV motor
- Propeller: HQ3020 2-blade props
Package
- 1 * F4 1S 12A AIO FC
- 4 * Anti-vibration rubber dampers
- 4 * M2 x 10mm screws
- 4 * M2 x 10mm screws
- 8 * M2 screw nut
- 1 * BETAFPV dipole T antenna (2.4G/46mm, only for ELRS RX version board)
- 8 * PH-1.25 connector for motor (not soldered, only for ELRS RX version board)
Betafpv.com offers a (30) day manufacture defect warranty, starting from the date the product(s) was delivered to the customer. If more than 30 days have passed since receiving your purchase, unfortunately we can’t offer you a refund or exchange.
For merchandise was confirmed as genuinely defective（Product Design problem & Quality issues）, we will ship out a replacement free of charge directly. The consumer will not be charged any fees for approved warranty service.
In almost all cases, we will work with you to debug your issue firstly.
Each claim should have all proof of defect by mean of photo or video showing clearly the defect of the product. Please create a ticket to send us photos or video of your product, a detailed description of your issue, and a description of what you have already done to fix it. We are happy to solve any problem you may meet.
NOTE: The refund amount is limited to the purchase price of the item.
Directly Send Ticket: Create a new ticket
*We do not accept ALL kinds of returns.
*All sales are final.
Affected by Covid-19, there will be some delay in the delivery.
Shipping Methods and Charges
- Standard Shipping
- Expedited Shipping (including DHL / FedEx / UPS. Can not ship batteries)
Note:
- Some remote address will be charged remote shipping fees according to the quotation of the logistics company.- FPV Goggles
- BETAFPV Gates & Flags
- RTF FPV Whoop Kits
- LiteRadio Series radio transmitter
- Radio Transmitter & Drone Storage Cases
For the strict Customs Policy, countries below are not available for delivering batteries. Therefore, if you fail to purchase from our site, hope can you understand that. We'll open selling once there is a reliable logistics channel.
-India (Both drones and batteries)
-Kuwait
Shipping Time:
Estimated Shipping Time:
- Expedited Shipping: 3-7 working days
- Standard Shipping (Registered Mail): 12-30 working days
* These are estimated delivery times only, BETAFPV can not guarantee an exact delivery time.
* The estimated delivery time may be longer if any battery included in your order.
* Affected by Covid-19, there may be some delay in the delivery.
* We accept no responsibilities and liabilities for delay in shipping time as this is beyond our control.
* Any problem about shipping info of your order, please contact Customer Support.
Battery Shpping Issues
More Info requried
- Taiwan or Hongkong: please fill your address and name in Chinese.
- South Korea: please provide your personal clearance code. If you do not have it, please apply it from this website:
https://unipass.customs.go.kr/csp/index.do - Brazil: please provide your tax number (CPF) in your address.
- Chile: please provide your individual tax number in your address.
How To Track My Parcel
We provide trackable shipping service to most of the package. Please click here to reach detail information.
Wrong Address
Shipments will be sent to the address entered on our web page during checkout. We cannot be held responsible if the incorrect shipping address is entered by the customer during checkout. We can only modify a wrong address if customer contacts us before the package is marked as shipped.We cannot change shipping addresses after the order has been shipped, as the address information you enter is used as part of the fraud checks and fraud prevention. If additional fees are required to re-ship packages due to address errors, those fees may be passed on to the customer.
Damaged box or incorrect item(s)
If you receive damaged or incorrect item(s), contact Customer Support in 5 business days with receipt of your shipment to make the necessary corrections.
* All duties and taxes are the responsibility of the customer.
